IEC 61058-1 PDF

IEC Standard | Switches for appliances – Part Requirements for mechanical switches. This part of IEC applies to switches for appliances. The switches are intended to control electrical appliances and other equipment for. This part of IEC applies to electronic switching devices and shall be used in conjunction with the general requirements of IEC

Author: Dizragore Kigal
Country: Guyana
Language: English (Spanish)
Genre: Photos
Published (Last): 9 June 2005
Pages: 70
PDF File Size: 6.33 Mb
ePub File Size: 19.71 Mb
ISBN: 942-4-55652-645-4
Downloads: 57028
Price: Free* [*Free Regsitration Required]
Uploader: Kajigami

NOTE 2 Certain electronic switches for example, passive infrared switches – “PIR switches” with adjustable time delay devices should be adjusted in such a way that the delay time is higher than the testing time, NOTE 3 Measured values within the test limits are acceptable for the results until the situation on uncertainty measurements has been clarified.

NOTE The test may be omitted when ongoing conformity is found e. Requirements for electronic switches. The force is applied by means of a straight -unjointed test finger of the same dimensions as the jointed test finger shown in figure’ 1 bflEC Arfnex T gives an example system for grouping switch types into switch families for this purpose Other grouping systems may also be appropriate for this purpose.

Occasional flickering of luminaires and irregular running of motors during the test are neglected. Compliance is ciiecked by inspection and by ttie tests in Tests may be carried 610588-1 with different test methods than those applied in conjunction with the type tests if the alternate test methods can be shown to be equivalent. Protection against qvervoltages — Section 610581 Use of coatings to achieve insulation coordination of printed board assemblies lEC The circuit is calibrated with the following tolerances: Electrostatic discharge immunity test.

BS EN IEC 61058-1:2018

The declared full travel of the actuating member if any shall oec applied during these tests. Compliance is checked by inspection and by applying the jointed test finger according to lEC without force. These switches are intended to be operated by a person, via an actuating member or by actuating a sensing unit.

Most Related  HAN KAMBER DATA MINING EBOOK PDF

Also covers the indirect actuation of the switch when the function of the ice member is provided by a part of an appliance or equipment. The actuating member or sensing unit can be integral with or arranged separately, either physically or electrically, from the switch and may involVe transmission of a signal, for example electrical, optical, acoustic or thermal, between the actuating member or sensing unit and the switch.

The circuit continuity Is ensured by soldering solely. For switches with electronic actuating members, actuation shall be performed according to the manufacturer’s declarations.

This standard is not included in any packages. General requirements [ETD Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.

Compliance is checked by the humidity treatment described in this subclause, followed immediately by he tests of Testing and measurement techniques — Section 2: Part 2 Symbols elements, qualifying symbols and other symbols having general application IS Part 1: Be the first to review this item Would you like to tell us about a lower price?

Attention is particularly drawn to the following: After the test, accessible ieec parts shall not be live It is not necessary for the samples to remain in operating condition. Each electronic switch is tested, if applicable, in the following states: For the tests of uec except electronic switches: Smaller clearances than those specified In table 22 are not allowed.

BS EN IEC – Switches for appliances. General requirements

Electronic cord switches and electronic independently mounted switches – without incorporated temperature-limiting devices or without incorporated fuses are tested according to If the temperature of the switch is limited by the operation of automatic protective devices including fusesthe temperature is measured 2 min after the operation of the device. NOTE 2 The heating occurring at full 16058-1 current of the end application with its rated duty-type, under the cooling conditions present at the end application, should not be higher than the values recorded during the lest 6058-1 thermal current.

Most Related  CORE JAVA BALAGURUSWAMY PDF

NOTE 2 No minimum thickness is specified for functional, basic, inaccessible supplementary and Inaccessible reinforced insulation. Compliance is checked by Inspection and by measurement.

NOTE Ttic temperature limits of table 13 are based on the values speciticct in lEC Since itiese values arc under consideration, it will be necessary to review tliem. It shall still be possible to actuate the actuating member to provide the appropriate disconnection.

BS EN 61058-1:2002+A2:2008

If a decorative cover is backed by an inner cover, fracture of the decorative cover is neglected if the inner cover withstands the test after removal of the decorative cover Unique Type Reference, U. Limits — Section 2: For electronic switches, the reduction to the break current should be achieved without any open circuiting of the simulated inductive loads circuit, to ensure that no abnormal voltage transients are generated.

NOTE 1 If any change of the setting occurs, it should be possible to restore the selling by operation of the eonlrol s. Table 24 – Minimum oreepage distances for functional instilation Table 25 -Test levels and conditions. Transmission of a signal between the actuating member or sensing unit and the switch may be connected by optical, acoustic, thermal, electrical or other relevant connection and may include remote controlled units.

No significant displacement or damage shall occur.

IEC – Estonian Centre for Standardisation

For switches of small dimensions, the marking may be on different surfaces. The variable control, if any, is set at the position of maximum output with any by-pass In open position.

No part of these publications ic be reproduced in any form without the prior permission in writing of BIS. The operating speed for the operating cycles shall be as follows: After the test, the specimens shall show no damage Impairing their further use or the safety of the 610058-1 switch.